China Big Embroideries

At first glance, the patte looks like a missing stitch. Corduroy is another type of fabric with an uneven surface. The method is to tear off the extra part by hand after embroidering, and then wash with water to completely dissolve all the water-soluble cloth. For example, in leather embroidery, the paper backing acts as a lubricant. In fact, it is not. It is a kind of paper that is thinner than the cut paper.

After embroidering, you can tear off the extra part at will.ufeffTypes of backing paper for computerized embroidery machines: Water-soluble cloth is most commonly used in terry cloth and flannel, as a surface lining to prevent wool. The backing is a layer of material laid under the fabric, which stabilizes the stitches and improves the smoothness of embroidery.

When it comes to embroidering special fabrics, such as terry cloth, velvet, blankets or velvet, because the surface is all long hair, it is easy to twist the threads between the woolen threads, and a layer of simplicity is added to prevent the embroidery threads from being entangled.

The use is roughly the same as that of water-soluble cloth, except that the hot melt should be Flat Computerized Embroidery Machines dissolved by heat, such as a roller-type hot press or an iron, and it will never affect the patte or leave any lining.

In addition, some high-priced products will use water-soluble cloth as a backing or surface lining to improve product quality. It is just that the pits on the cloth surface cause the stitches to sink. After the embroidery is completed, the remaining part can be cut off.

China Big Embroideries...

The thread used for bottoming is too thin or the angle is wrong, and the fabric cannot be fixed well. Because the paper under the fabric is too thin, it can't line up the fabric well. The computerized embroidery patte-making should consider the overall rationality of the needle; if you don’t walk a single needle in a local area, then just go straight to the place far away from the single needle to embroider a large flower, and then retu to use the needle package.

ufeffThere are ten main reasons for the patte movement of the computerized embroidery locomotive: China Spray Printing Embroidery Machines Manufacturers When making a patte, it should be printed from the center to the periphery as much as possible, so as to be more stable in the production process.

The single needle is wrapped up, so it’s very common to move in this way, it is not visible in the software, and it changes on the embroidery machine. The pulling force of the {cloth} paper on the embroidery machine should be just right, not too strong, otherwise it will change very simply Increasing the number of line changes will reduce the output power, but the possibility of positioning will decrease a lot, depending on how you combine the two. During the patte-making process, the bottom line is too close to the edge of the object.

Due to the repeated use of double-sided adhesive tape during the production process, the viscosity is reduced and the fabric is unable to be fixed. Due to the aging of the machine, the precision decreases and the position is shifted, such as: the same batch of embroidery, some are normal, and some are shifted Because the fluff on the surface of the cloth forms a position, it is more obvious when the cloth is pasted on the flannel.

China Big Embroideries...

Use a multimeter to measure whether the power board transistor M5 malfunctions? If there is any problem: change the transistor of the same model. Use a multimeter to measure the plug 4 and 5 of the socket CZ6 on the power board in the control box, and the exchange voltage should be 63V.

 

Inspect whether the signal line connection between the main control board and the power board is reliable. If not abnormal: remove the embroidery frame. Use the resistance file of a multimeter to check whether there is a short circuit between the wire-deduction magnet lead and the frame (resistance is 0): Inspect each wire-deduction magnet in tu, and replace it. The accurate resistance value should be 10; or more.

 

Use a multimeter to measure the DC voltage of pins 2 high speed embroidery machines price and 3 of the socket CZ3 on the power supply board in the control box should be 90V u0026 plusmn; 10%. Inspect whether the connection between the buckle magnet and the power board can be reliably connected: check to make the connection reliable. If it is not accurate: Check whether the plug-in department is superior in battle; exchange the power board.

 

ufeffReflective methods and processing steps for embroidering machine thread deduction: Inspect whether the main control board has a wire-cut signal input, can the wire-cut indicator L32 (KX) be lit? If L32 (KX) does not light up, it indicates that there is a problem with the control board (no signal input): exchange the main control board.

China Big Embroideries...